26 Jan ASTM A gives information on recommended steel chemistry for steel to be galvanized, as well as required venting/drainage hole. ASTM A/A M. Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip) provides details on steel selection and other design practices such as. ASTM Apdf – Download as PDF File .pdf), Text File .txt) or read online.
|Published (Last):||21 June 2007|
|PDF File Size:||20.29 Mb|
|ePub File Size:||4.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
This test method a38 with the standard procedures for establishing the relative bond strength of steel reinforcing bars in concrete using beam-end specimens. Moving parts such as handles or astm a385 should be galvanized separately and assembled after galvanizing. Heat analysis shall be astm a385 to determine the percentage of carbon, manganese, phosphorus, sulfur, vanadium, nickel, chromium, molybdenum, columbium, and copper for the required chemical composition.
Assemblies should consist of elements astm a385 similar chemistry and surface condition. The following is a summary of the various astm a385 hot-dip galvanizing specifications. The adherence requirement is the same as A, for strong bond throughout the life of the hot-dip galvanized steel.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Finally, the adherence requirement astm a385 for the entire coating to have a strong adherence throughout the service life of the galvanized steel.
Specification astm a385 Structural Steel. This specification covers carbon structural steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes. The purpose of the calculation is to provide justification for the purchase of asgm higher initial cost system with a low life-cycle cost over an initially less expensive coating which has high future costs.
Common distorted and warped members of assemblies are sheets or plates assembled by welding or riveting. Work Item s – proposed revisions of this standard. Standard Specification for Zinc Astm a385 Galvanized Coatings on Iron and Steel Products covers individual steel pieces as well as assemblies of various classes of material. The astm a385 can cause warpage and distortion: Purchase a copy from the AGA, or contact your local galvanizer. Welding flux residues shall be removed by standard galvanizing cleaning techniques and are best removed at the gun.
Historical Version s – view previous versions of standard.
ASTM-A | Ahmed Negm –
The requirements for finish, appearance, and adherence are identical to those in the other main standards. ASTM A Practice for Repair astm a385 Damaged and Uncoated Areas of HOt-Dip Galvanized Coatings covers appropriate methods used to repair damaged hot-dip galvanized coatings on hardware, structural shapes, and other hot-dip galvanized products, including uncoated areas remaining after initial hot-dip galvanizing.
These differences include excessively rusted astm a385, pitted surfaces, machined surfaces, a3385 iron especially astm a385 sand inclusion, cast steel, malleable iron, hot-rolled steel, and cold-rolled s385.
Eddy-current-type thickness measurement is a non-destructive test measuring variations in the impedance of an eddy-current inducing coil caused asm coating thickness variations. It may also be known by its trade name, astm a385.
However, if the galvanizer has to perform additional work in order to prepare the product for hot-dip galvanizing, such as drilling holes to facilitate drainage or venting, the galvanizer will astm a385 and resolve the issue with the customer. This test astm a385 shall determine the effects of surface preparation or condition such as bar coatings on the bond strength of deformed steel reinforcing bars to concrete.
A358 astm a385 coating thickness minimums, but no maximums, and the threads are not subject to the coating thickness requirement. The specification astm a385 three acceptable forms of touch-up: However, the AGA does provide a compilation of specifications pertinent to galvanizing. The material categories covered in the specification include structural steel and plate, strips and bars, pipes and tubing, and wires.
Rebar is commonly bent prior to galvanizing, and the recommendations for diameter and astm a385 practices are provided in A Requirements concerning the renovation of uncoated areas after initial hot-dip galvanizing are contained within the material specifications A, A, A This tubing shall be produced in both welded and seamless sizes and must have the chemical requirements ast, carbon, astm a385, phosphorus, sulfur, and copper.
All oil or grease should be removed from both the sheet steel and wire or rod before rolling. Types of embrittlement commonly encountered with galvanized steel are related to aging phenomena, cold working, and absorption of hydrogen.
Inch-pound units asgm SI units astm a385 not necessarily exact equivalents. The requirements astm a385 the specification facilitate the production of a high-quality zinc coating and are similar to those found in A and A It is aastm responsibility of astm a385 designer asm fabricator to ensure the product has been properly designed and built before the hot-dip galvanizing process supporting specifications. This abstract is a brief summary of the referenced standard.
This specification covers astm a385 welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes.
What are the differences between ASTM A123/A123M and ASTM A385?
Whenever different analyses of steel or different surfaces of steel are united in an assembly the galvanized finish is not generally uniform astm a385 appearance. This specification covers black astm a385 hot-dipped galvanized asgm welded and seamless carbon steel square, round, rectangular, or special shape structural tubing for welded, riveted, or bolted construction or bridges and buildings, and for general astm a385 purposes.
Within the text of this specification and where appropriate, SI units are shown in brackets. Embrittlement is the loss or partial loss of ductility in a steel where an embrittled product characteristically fails by fracture without appreciable deformation.
They can only be used if the electrical conductivity of the coating differs significantly from that of the substrate. Any combination of these products can be astm a385 into a single fabrication and then hot-dip galvanized.
All markings shall remain legible after galvanizing.