Quality Expanded Metal; ASTM F TYPE1 CLASS 1 4FT X 8FT; 1/2 #18 Standard NSN: ASTM F Standard Specification for Metal, Expanded, Steel. ASTM F Standard Specification for Metal, Expanded, Steel. standard by ASTM International, 03/01/ View all product details. Most Recent.

Author: Yozshukazahn Mikarisar
Country: Reunion
Language: English (Spanish)
Genre: Business
Published (Last): 7 March 2006
Pages: 139
PDF File Size: 4.42 Mb
ePub File Size: 15.70 Mb
ISBN: 498-5-45482-284-6
Downloads: 37408
Price: Free* [*Free Regsitration Required]
Uploader: Megrel

The deviation in inches from the original plane when the grating is placed under a load.

ASTM F Steel Expanded Metal , Steel Finished Product

Welded Bar Grating Stair Treads 6 Welded stair treads are manufactured from standard Grating with a patterned floor plate nosing and pre-punched end plates to facilitate installation.

Building Entrances, Air Duct and sidewalk installations when ventilation and easy wstm are required. There are very few differences between the two expanded metal specifications.

A load that is equally distributed over all of the clear span. Because of all the angles in expanded metal, getting into the diamond becomes an exercise in patience. They may legitimately differ from the normal, pattern-sized sheets generally stocked and sold by metal service centers.

Manufacturers of shopping carts, lockers or furniture often have their own internal requirements for expanded metal. If the sheet delivered weighs less than Heavy Duty Grip Strut is a one-of-a-kind plank grating sporting a hefty 24 foot clear span capability.

ASTM F1267-07 Steel Expanded Metal

Below is an introduction to both specs. The distance between supporting members measured from the inside bearing point of one supporting member to the inside bearing point of the next supporting member.


Next, weigh the sheet.

Finally, the sheet size must also be specified. Historical Version s – view previous versions of standard. Raised ff1267, with its multiple facets, is what comes out of the expanding press. F167 measure the strand thickness, the calipers must be flat against the thickness of the bond. Flattened Aluminum 7 Aluminum Alloys: Measuring standard expanded metal can be tricky even for the most experienced warehouse person armed with good calipers.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. As thicker material is used to produce a given product, the strand width can be reduced to compensate, thereby keeping the weight per square foot the same. All close mesh types shown sstm are with 4 inch cross bar centers.

Bushwick Metals Conditions of Sales. The values given in parentheses are for information only and may be approximate.

Expanded products typically are produced in 4-by-8 sheets, but many sizes are available. To protect themselves from receiving inferior products, service centers would be well advised to source expanded metal from suppliers, both domestic and foreign, that adhere to these standards. Each single strand test specimen shall be visually inspected, and that surface of the strand observed to have the most nearly uniform coating shall be the tension surface when the strand is subject to bending.


Could you measure it to see if it conforms to the specification?

Expanded metal shall be manufactured with the corresponding thickness, design size, opening size and strand size. Expanded Metal Grating 12 Concentrated Load: It is informational only and not an official part of the standard; t1267 full text of the standard itself must be referred to for its use and application.

These are generally designed for adtm specific purpose and might be produced to meet some other, more important criteria, such as fitting into a jig. Special fabrication, cutting or specialty configurations available upon request and special quotation.

What You Need to Know. For each additional inch add the appropriate weight from table for Bearing Bar Sizes. Over time, industry practice has made some of these designations less accurate. Non-standard, cut to size expanded metal. Concentrated loads are shown in per ft. The issue is that some producers may utilize thinner materials and still narrow the strand width, delivering an inferior product.

Author: admin