LENZE 8600 MANUAL EBOOK

View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. Manuals and User Guides for Lenze series. We have 1 Lenze series manual available for free PDF download: Operating Instructions Manual. Planning 1 Features of the inverter series Liability • The information given in these Operating Instructions describe the features of the products but do not.

Author: Akinokasa Douzil
Country: Saudi Arabia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 17 August 2006
Pages: 238
PDF File Size: 7.92 Mb
ePub File Size: 7.89 Mb
ISBN: 345-5-54660-725-2
Downloads: 84659
Price: Free* [*Free Regsitration Required]
Uploader: Mall

Page 85 Enabling the additional acceleration and deceleration times With lenze 8600 manual control activate the assigned digital inputs according to the table below. The acceleration and deceleration times refer to a Change of the field frequency from 0 to lenze 8600 manual maximum field frequency set under CO1 1.

For detailed explanations of the Codes and their possible functions refer to the corresponding chapters.

LENZE SERIES OPERATING INSTRUCTIONS MANUAL Pdf Download.

The EMC can only be checked when integrating the controller into a drive system. Tell us about it. The ramp times 860 the ramp generator are set separately via C and C A function which is already assigned to an output, can only be assigned to another terminal or the relay output, if the previously lenze 8600 manual manul has lenze 8600 manual assigned to another function.

If the set-value is smaller, the obtainable adjustment result is normally less precise. Voltage boost Vmin In the low speed range, the obtained torque is determined largely by the set voltage boost.

TOP Related Posts  FM 34 60 COUNTERINTELLIGENCE EPUB

The RFI filter must always be connected to earth at first even if you only want to test the system. The configuration determines whether the input is unipolar, bipolar, or independently of the operating mode, a digital frequency input.

Technical Data Of Mains Lenze 8600 manual Setting Of The Torque Controller Technical data General data M a i n s v o lenze 8600 manual t a g e: The quality of the control behaviour is set via the Vp-gain factor CO77 and the adjustment time Tn C To reach also higher numbers with this version, the accessible range can be changed by code C Analog Inputs And Outputs The lower the max.

Ensure unimpeded ventilation of cooling air.

Selection Of The Mains Choke Control Mode Gain the Signal gain after the offset adjustment. Digital lenze 8600 manual output X9 Option The connection of drives via digital lenze 8600 manual allows a simple and or Slave drives.

For further information about the flying restart circuit see page Before you tan use the DGinjection brake, set the brake voltage and therefore the brake torque.

Diameter And Radius Detection During a warning the signal “ready” is removed, however, the operation of the frequency inverter is not interrupted.

Terminals The terminals are exclusively used to control the inverter.

Lenze 8600 series Manuals

Code table The following table Shows which settings you tan enter under which Codes. Page 98 Rated motor power By entering the rated motor power Cthe flying restart circuit is adapted to the motor. Parameter Acceptance lenzw Your page settings Preselection: For master-Slave lenze 8600 manual it is important that, in case of Speed A frequency Signal which is proportional to the field frequency tan be supplied to terminal X9.

TOP Related Posts  IGLS ALGORITHM FILETYPE PDF

Technical Data Of Sine Filters 6. Observe data of the motor manufacturer. Configuration Using code CO05 you tan determine the internal control structure and the use of the setpoint and act. Page 89 Enabling the additional acceleration and lenze 8600 manual times With terminal control activate the assigned digital inputs according to the table below. Zinc-coated mounting plates allow a permanent contact. The fault is displayed automatically under C Initial lenze 8600 manual on After mains connection the controller is ready to operate after approx.

The motor filter reduces capacitive currents caused by parasitic cable capacitances. Comments to this Manuals Your Name. The large lenze 8600 manual ranges of the control parameters also allow the control of an application datum if lenze 8600 manual depends on the drive speed. Additional module for the Lenze series, Slave connection module for the communication System Can be integrated into the base controllers Can be combined with the automation modules PP, The process control can consist of a maximum of eight process steps.

When using motors which do not have majual suitable insulation for inverter operation: Lenze 8600 manual means, the drive could accelerate to fmax while adjusting the inputs when the setting controller enable is activated, although only a very small setpoint was